blob: e09c1ea5ec4b98fb161f680a48c4255950a85896 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
|
# livecd-stage1 example specfile
# used to build a livecd-stage1
# The subarch can be any of the supported catalyst subarches (like athlon-xp).
# Refer to the catalyst reference manual for suppurted subarches.
# http://www.gentoo.org/proj/en/releng/catalyst/reference.xml
# example:
# subarch: athlon-xp
subarch:
# The version stamp is an identifier for the build. It can be anything you wish# it to be, but it is usually a date.
# example:
# version_stamp: 2005.0
version_stamp:
# The target specifies what target we want catalyst to do. For building a CD,
# we start with livecd-stage1 as our target.
# example:
# target: livecd-stage1
target:
# The rel_type defines what kind of build we are doing. This is merely another
# identifier, but it useful for allowing multiple concurrent builds. Usually,
# default will suffice.
# example:
# rel_type: default
rel_type:
# This is the system profile to be used by catalyst to build this target. It is# specified as a relative path from /usr/portage/profiles.
# example:
# profile: default-linux/x86/2005.0
profile:
# This specifies which snapshot to use for building this target.
# example:
# snapshot: 20050324
snapshot:
# This specifies where the seed stage comes from for this target, The path is
# relative to $clst_sharedir/builds. The rel_type is also used as a path prefix# for the seed.
# example:
# default/stage3-x86-2004.3
source_subpath:
# These are the hosts used as distcc slaves when distcc is enabled in your
# catalyst.conf. It follows the same syntax as distcc-config --set-hosts and
# is entirely optional.
# example:
# distcc_hosts: 127.0.0.1 192.168.0.1
distcc_hosts:
# This is an optional directory containing portage configuration files. It
# follows the same syntax as /etc/portage and should be consistent across all
# targets to minimize problems.
# example:
# portage_confdir: /etc/portage
portage_confdir:
# The livecd-stage1 target is where you will build packages for your CD. These
# packages can be built with customized USE settings. The settings here are
# additive to the default USE configured by the profile. For building release
# media, the first thing we do is disable all default USE flags with -* and then
# begin to set our own.
# example:
# livecd/use: -* ipv6 socks5 livecd fbcon ncurses readline ssl
livecd/use:
# This is the set of packages that we will merge into the CD's filesystem. They
# will be built with the USE flags configured above. These packages must not
# depend on a configured kernel. If the package requires a configured kernel,
# then it will be defined elsewhere.
# example:
# livecd/packages: livecd-tools dhcpcd acpid apmd gentoo-sources kudzu-knoppix hotplug coldplug fxload irssi gpm syslog-ng parted links raidtools dosfstools nfs-utils jfsutils xfsprogs e2fsprogs reiserfsprogs ntfsprogs pwgen rp-pppoe screen mirrorselect penggy iputils hwdata-knoppix hwsetup lvm2 evms vim pptpclient mdadm ethtool wireless-tools prism54-firmware wpa_supplicant
livecd/packages:
|
GitWeb
